 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Features * Duplex LC Single Mode Transceiver * Small Form Factor Multi-soured 2 x 5 Pin Package * Complies with ITU-T/STM-4, OC-12 * 1310nm / 1550nm Wavelength, FP / DFB Laser * Single+3.3V Power Supply * LVPECL Differential Inputs and Outputs * LVPECL Signal Detection Output [C-1X-622-F(DFB)-SLC(4)] * Temperature Range: 0 to 70oC * Class 1 Laser International Safety Standard IEC 825 Compliant * Solder ability to MIL-STD-883, Method 2003 * Pin coating is Sn/Pb with minimum 2% Pb content * Flammability to UL94V0 * Humidity RH 5-85% (5-95% short term) to IEC 68-2-3 * Complies with Bell core GR-468-CORE * Uncooled laser diode with MQW structure * ATM 622 Mbps Links application * SONET/SDH Equipment Interconnect application Absolute Maximum Rating Parameter Power Supply Voltage Output Current Soldering Temperature Operating Temperature Storage Temperature Symbol Vcc Iout - Min. 0 0 0 -40 Max. 3.6 30 260 70 85 Unit V mA C C C Note 10 seconds on leads only Topr Tstg Recommended Operating Condition Parameter Power Supply Voltage Operating Temperature (Case) Operating Temperature (Case) Data Rate Symbol Vcc Topr Topr Min. 3.1 0 -40 Typ. 3.3 622 Max. 3.5 70 85 Unit V C C Mbps C-1X-622-F(DFB)-SLC(4) C-1X-622-F(DFB)-SLC(4)A Note LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 1 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Transmitter Specifications, (0C Compliant with ITU-T G.957/STM-4 Eye Mask Transmitter Specifications, (0C 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 2 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Receiver Specifications, (0C 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 3 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Connection Diagram PIN 1 2 3 4 5 6 7 Warnings8 9 10 Symbol RxGND RxVcc SD RDRD+ TxVcc TxGND TxDIS TD+ TD- Notes Directly connect this pin to the receiver ground plane +3.3V dc power for the receiver section Active high on this indicates a received optical signal(LVPECL) Receiver Data Out Bar (LVPECL) Receiver Data Out (LVPECL) +3.3V dc power for the trasmitter section Directly connect this pin to the transmitter ground plane Transmitter disable (LVTTL) Transmitter Data In (LVPECL) Transmitter Data In Bar (LVPECL) The attaching posts are at case potential and may be connected to chassis ground. They are isolated from circuit ground. Attaching Posts LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 4 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Recommended Circuit Schematic PHY DEVICE TERMINATE AT TRANSCEIVER INPUTS Vcc(+3.3V) Z=50! TD- 100! LVPECL Z=50! 130! 1"H TD+ 10 TD- 9 TD+ 8 TxDIS 7 TxGND 6 TxVcc Vcc(+3.3V) C3 Tx Rx C2 10"F RxGND RxVcc RD+ RD- SD 1"H C1 Vcc(+3.3V) RD+ 1 2 3 4 5 Z=50! 100! RD- LVPECL Z=50! 130! 130! Z=50! Vcc(+3.3V) 130! SD 82! NOTE:C1=C2=C3=100nF TERMINATE AT DEVICE INPUTS The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 5 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Printed Circuit Board Layout Consideration A fiber-optic receiver employs a very high gain, wide bandwidth transimpedance amplifier. This amplifier detects and amplifies signals that are only tens of nA in amplitude when the receiver is operating near it's limit. Any unwanted signal current that couples into the receiver circuitry causes a decrease in the receiver's sensitivity and can also degrade the performance of the receiver's signal detect (SD) circuit. To minimize the coupling of unwanted noise into the receiver, careful attention must be given to the printed circuit board. At a minimum, a double-sided printed circuit board(PCB) with a large component side ground plane beneath the transceiver must be used. In applications that include many other high speed devices, a multi-layer PCB is highly recommended. This permits the placement of power and ground on separate layers, wich allows them to be isolated from the signal lines. Multilayer construction also permits the routing of signal traces away from high level, high speed sinal lines. To minimize the possibility of coupling noise into the receiver section, high level, high speed signals such as transmitter inputs and clock lines should be routed as far away as possible from the receiver pins. Noise that couples into the receiver through the power supply pins can also degrade performance. It is recommended that a pi filter be used in both transmitter and receiver power supplies. EMI and ESC Consideration OIC transceivers offer a metalized plastic case and a special chassis grounding clip. As shown in the drawing, this clip connects the module case to chassis ground then installs flush through the panel cutout. This way, the grounding clip brushes the edge of the cutout in order to make a proper contact. The use of a grounding clip also provides increased electrostatic protection and helps reduce radiated emission from the module or the host circuit board through the chassis faceplate. The attaching posts are at case potential and may be connected to chassis ground. They should not be connected to circuit ground. Plastic optical subassemblies are used to further reduce the possibility of radiated emission by eliminating the metal from the transmitter and receiver diode housings, which extend into connector space. By providing a non-metal receptacle for the optical cable ferrule, the gigabit speed RF electrical signal is isolated from the connector area thus preventing radiated energy leakage from these surfaces to the outside of the panel. Recommended Board Layout Hole Pattern DIMENSION IN MILLIMETER (INCHES) NOTES: 1.THIS FIGURE DESCRIBE THE RECOMMAND CIRCUIT BOARD LAYOUT FOR THE SFF TRANSCEIVER. 2.THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFF. NO METAL TRACES OR GROUND CONNECTION IN KEEP-OUT AREAS. 3.THE MOUNTING STUDS SHOULD BE SOLDERED TO CHASSIS GROUND FOR MECHANICAL INTEGRITY. LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 6 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(DFB)-SLC(4) Recommended Panel mounting DIMENSION IN MILLIMETER (INCHES) Package Diagram 48.8+0 -0.2 (1.921) +(.000) -(0.008) "3.6 +0 -0." (0.535) +(.000) -(0.004) "5.08 (0.594) (0.520) 6.97 (0.274) (0.531) (0.386) +(.000) -(0.004) 9.8 +0 -0." "".36 (0.374) (0.447) 2."8 (0.155) (0.086) 3.95 "3.50 (0.400) (0.386) 13.20 9.50 10.16 (0.150) O1.00!0.05 (0.039)(0.002) (0.700) (0.020) (0.070) 3.81 (0.413) 10.50 0.50 1.78 17.78 (0.280) 7.12 (0.200) 5.08 (0.246) 6.25 LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 9.80 7 LUMNDS595-JUL1504 rev. A.1 622 Mbps Single Mode SFF LC Transceiver C-1X-622-F(FDFB)-SLC(4) Available Options: C-13-622-F-SLC C-13-622-FDFB-SLC4 C-15-622-FDFB-SLC4 C-13-622-F-SLCA C-13-622-FDFB-SLC4A C-15-622-FDFB-SLC4A Part numbering Definition: C - 1X - 622 - F(DFB) - S LC TxPower Temperature Range * 13 = Wavelength 1310nm 15 = Wavelength 1550nm * Communication protocol (622 Mbps) * F = +3.3V SFF Transceiver, FP FDFB = +3.3V SFF Transceiver, DFB * Single mode fiber * Connector options * Tx Power range Blank = -15 to -8 dBm 4 = -3 to +2 dBm * Temperature range Blank = commercial temperature(0 to 70 C) A = industrial temperature(-40 to 85 C) Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC's sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company's standard one-year warranty; however, specifications designated as "preliminary" are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company's Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. (c) LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. * Chatsworth, CA 91311 * tel: 818.773.9044 * fax: 818.576.9486 9F, No 81, Shui Lee Rd. * Hsinchu, Taiwan, R.O.C. * tel: 886.3.5169222 * fax: 886.3.5169213 8 LUMNDS595-JUL1504 rev. A.1 |
Price & Availability of C-15-622-FDFB-SLC4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |